Emergency thil avanga circuit pressure a tlahniam chuan clamping force tlahniam theihna a awm a, workpiece pawh a tla thei bawk. Mipui hliam emaw, hmanrua chhiat emaw ven nan chuan tlu lo tur venna hmanrua dah a ngai a ni.
2. Pneumatic fingers hi pawn lam chakna nasa lutuk emaw, impact emaw avanga hman loh tur.
3. Single-action type tan chuan spring force chauhin a chelh laiin kan company nen inrawnkhawm rawh.
4. Pneumatic finger cylinder i dah leh siamthat dawnin a tlak loh tur, a insu lo tur a ni a, a tichhia lo tur a ni.
5. Clamping爪 accessories i siam that hunah, khawngaihin clamping爪 chu twist suh.
6. Pneumatic fingers te hian a hnuaia installation dan te hi an nei a. Screw-te tightening torque chu a hnuaia table-a tarlan torque range chhungah a awm tur a ni. A lian lutuk chuan hnathawh \\ha lo a thlen ang; a tlem lutuk chuan position deviation leh falling off a thlen ang.
7. Gripper accessories dah dan tur: 1.1.
Gripper accessories i dah dawnin fimkhur hle ang che. Gripper chu man turin open-end wrench chauh hmang la, chutah chuan internal hexagonal wrench hmangin screw te kha tikhauh rawh. Taksa chu direct-in man suh la, chutah chuan screw-te chu khauh takin khauh rawh; chutiang a nih loh chuan a components te chu tihchhiat a awlsam hle.
8. Gripper-ah hian pawn lam chakna dang dah belh loh tur. Lateral load hian gripper-ah hna a thawk a, impact load a siam a, chu chuan gripper chu a ti nghing a, a chhe bawk. Clearance chu pneumatic fingers te chu stroke tawp lama workpiece leh accessories te nen an inhnaih loh nan set rawh.
8.1, stroke tawp lamah pneumatic fingers te chu open position-a an awm laiin;
8.2. Pneumatic fingers te hi stroke tawp thlengin an kal thin.
8.3. Action status chu reverse rawh.
Reversing operation kan tih hian workpiece clamp na hmun chu a dik tur a ni. Chutiang a nih loh chuan reversing state chhung hian workpiece chu a chhehvel boruak nen a insu thei a, chu chuan impact load a siam thei a ni. Workpiece insertion action neih chhung hian mhz2-16d cylinder-a pawn lam force dang siam chhuah loh nan center line chu coaxial a ni tur a ni a, eccentric a ni tur a ni lo. A bik takin test run neih chhung hian himna tur, engmah nghawng emaw, thil dang emaw awm lovin, speed hniam taka hnathawh theih nan manual operation leh pressure tihhniam a ngai a ni.
9. Khawngaihin gripper hawn leh khar speed chu speed control valve emaw a ang chi hmangin siamrem la, a hawn leh khar thuai loh nan.
10. Pneumatic fingers kalna kawngah tumah luh phal a ni lo va, chutah chuan thil dah phal a ni lo bawk.
11. Pneumatic fingers te i lakchhuah dawnin compressed air i chhuah hmain workpiece i vawn loh nan finger la, chutah chuan fingers te chu i la chhuak leh ang.
A chungah hian mhz2-16d cylinder hman dan te, mhz2-16d cylinder chhunga dah dan te, A kaihhnawih hriat belh duh chuan tlawh theih a nihttps://www.joosungauto.com/ ah hian a awm bawk..
